BRP GTX Series Specifications

Mmo-2006 4x6 REV ANG.FH8 Fri Apr 29 15:30:56 2005 Page 1 CompositeC M Y CM MY CY CMY K

INTRODUCTIONEveryone is a beginner the first time he sits behind the controls of asnowmobile regardless of previous experience in driving an automo-bi

Headlight FuseHeadlight is protected with 20 ampere rated fuse. See followingillustration for fuse holder location. If headlight does not light up,che

Electric-Start Liquid Cooled Models except SDICharging System FuseCharging system is protected with 30 ampere rated fuse. See fol-lowing illustration

ECM FuseElectric Start Liquid Cooled Models Except SDIECM is protected with 5 ampere rated fuse. See following illustra-tion for fuse holder location.

SDI ModelsOpen front hood.To open fuse box push on cover tab and tilt cover.1A32I0KATYPICAL1. Push tab_________________________101

2A32I0IA1 3TYPICAL1. Fuse description decal2. Fuse remover/installer3. Spare fuses102_________________________

1A32I0JATYPICAL1. Fuse remover/installerElectric Fuel Level Gauge FuseSee an authorized SKI-DOO dealer for fuse replacement.31) Front Grab Handle/Fron

mmo2006-003-050_a1. Front grab handleCAUTION: Do not use skis to pull or lift snowmobile.32) Storage CompartmentWARNINGAll storage compartments must

All X Package Except Summit Models1A33H1ZA1. Storage compartment coverAll Models Except X Package and GTXPull latch slightly upward then, backward to

GTX ModelsA33H4UA11. Storage compartment33) Rear RackWARNINGAll objects in rear rack must be properly latched. Do not carryany breakable objects. Exc

A33B0QA 11. Tool kit35) SuitcaseGTX LimitedCAUTION:MAXIMUM load for each suitcase is 4 kg (9 lb).Unlock the suitcase from its support by turning the u

IMPORTANT BASIC SAFETY MEASURESTraining Basic training is required for the safe operation of any snowmo-bile. Study your Operator's Guide paying

A33A2SA11. Upper buttonA33A2UA11. Locking deviceLift suitcase to release it from its lower support.108_________________________

A33A2TASuitcases can be locked on vehicle using the safety locking device,usingthisdevicewillpreventthesuitcasereleasebuttontoturn.A33A2UA11. Locking

36) Integrated BagGSX Liquid Cooled ModelsLift release lever from plastic buckles to unfasten integrated bagfrom vehicle.A33A2VA110___________________

37) 2+1 SeatGTX Limited3 Passenger's Seat Set-UpTheGTXLimitedhas3seats.A33A2WA3 2 13 PASSENGER'S SEAT SET-UP1. Driver seat2. 2+1 seat3. Pass

WARNING– NEVER place any cargo on either of the 2 passenger seats,as cargo could collide with occupants.– If you ride with the 2 passenger seats inst

WARNING– NEVER ride with the “2+1” seat installed if the rearmostpassenger’sseatisnotinstalled.– The “2+1” seat must rest against the passenger’s sea

A33A2ZAPULL PASSENGER'S SEAT REARWARDSlightly pull 2+1 seat rearward to release alignment tab from driverseat.Remove 2+1 seat.114________________

A33A30APULL 2+1 SEAT REARWARDNOTE: When the “2+1” seat is removed, you must always proceedto the reinstallation of the passenger’s seat (the one with

mmo2006-003-019IMPROPER 2 PASSENGER'S SEAT SET-UPCAUTION: Take care to store the 2+1 seat properly to avoid anydamages.Reinstall passenger's

A33A2XA121. Driver seat2. Passenger's seatWARNINGMake sure the passenger's seat(s) that are installed are lockedsecurely in place before us

 Always keep a safe distance from other snowmobiles and by-standers. Remember, promotional material may show risky maneuvers per-formed by professio

A33C02A1TYPICAL — SPARK PLUG HOLDER ON LEFT HAND SIDE PANEL1. Spare spark plugs installed in holderNOTE: Spare spark plugs are not supplied with snowm

mmo2006-003-020LIQUID COOLED — SPARE DRIVE BELT INSTALLED IN HOLDERmmo2006-003-026_aFAN COOLED — SPARE DRIVE BELT INSTALLED IN HOLDER1. Push drive bel

40) HitchThe hitch can be used to pull most equipment. Use a rigid tow bar.41) Shields and GuardsWARNINGNever operate engine without belt guard secur

A00A8KA12TRACK SYMBOLS1. Approved2. NOT ApprovedGenerally, snowmobiles adapted for mountain riding comes withtracks equipped with high lug profiles. T

RECOMMENDED FUEL AND OILRecommended FuelUse regular unleaded gasoline, available from most service stationsor oxygenated fuel containing a maximum tot

When using non-oxygenated fuel, we highly recommend the use ofisopropyl base gas line antifreeze in a proportion of 150 mL (5 U.S.oz) of gas line anti

CAUTION: Never use four-stroke petroleum or synthetic motoroil and never mix these with outboard motor oil. Do not useNMMA TC-W, TC-W2 or TC-W3 outboa

BREAK-IN PERIODEngineCAUTION: A break-in period of 10 operating hours — 500 km(300 miles) — is required before running the snowmobile at fullthrottle.

OPERATING INSTRUCTIONSPre-Operation CheckWARNINGThe pre-operation check is very important prior to operatingthe vehicle. Always check the proper oper

• Verify that skis and steering operate freely. Check correspondingaction of skis versus handlebar.• Check fuel and oil for levels and leaks. Replenis

 Venturing out alone with your snowmobile could also be haz-ardous. You could run out of fuel, have an accident, or damageyour snowmobile. Remember,

PRE-OPERATION CHECK LISTITEM OPERATION ✔Body includingseat, footrests,lights, controls andinstrumentsCheck that there is no snow or ice.Track and idle

Procedure• Recheck throttle control lever operation.• Ensure that the tether cord cap is in position and that the cord isattached to your clothing eye

Choke ApplicationInitial Cold Starting When Temperature is Below - 10°C(+15°F)NOTE:Do not operate the throttle lever with the choke lever on.Set the c

Procedure (Cont'd)Manual Starting• Grab manual starter handle, pull handle slowly until a resistanceis felt, then hold handle firmly and pull vig

WARNINGMake sure wide-base snowmobile mechanical stand is stable.Stay clear of the front of vehicle and the track. Do not use toomuch throttle during

For factory recommended adjustments refer to decal on belt guard.It describes settings for optimum comfort according to load for yourSKI-DOO model.Cho

WARNINGDo not attempt to lift the vehicle by hand alone. Use appropri-ate lifting device to avoid risk of strain injuries. Always makesure the liftin

CBAmmo2006-003-022_aTYPICAL — PROPER ADJUSTMENTA. Suspension fully extendedB. Suspension has collapse with driver, passenger(s) and load addedC. Dista

CAUTION: To increase preload, always turn the left side adjust-ment cam in a clockwise direction, and the right side cam in acounterclockwise directio

WARNINGBefore proceeding with any suspension adjustment, remem-ber:– park in a safe place– remove tether cord cap– lift rear of vehicle off the groun

 Ensure the path behind is clear of obstacles or bystanders beforeproceeding in reverse. Do not leave your keys in the ignition switch, it is an inv

Stopper Strap — Weight Transfer• Ride at low speed then fully accelerate.• Note steering behavior.• Adjust stopper strap length accordingly.WARNINGBe

Strap AdjustmentAll Models except SummitA03F0QB1TYPICAL1. Increase or decrease strap length by bolting to a different holeSummit ModelsA32E19A11. Loos

Coupling Blocks — HandlingSC4 Suspension Only• Ride at moderate speed and check for desired handling.• If handling requires adjustment, turn both left

Rear Shock Motion Ratio — Damping StrengthX Package OnlyRear shock on the above mentioned models feature 2 adjustments.Low Speed Compression AdjusterT

WARNINGBefore proceeding with any suspension adjustment, remem-ber:– park in a safe place– remove tether cord cap– lift rear of vehicle off the groun

Preload AdjustmentScrew Type Shock2A32F1CA11. Increase or decrease spring preload2. Position numberCAUTION: Make sure that both front springs are stil

Cam Type ShockA03F2IA11. Increase or decrease spring preloadCAUTION: Make sure that both front springs are still pre loadedwhen front of vehicle is of

SUSPENSION TROUBLESHOOTING CHARTProblem Corrective measuresFront suspensionwandering– Check ski alignment and camber angle adjustment.See an authorize

SPECIAL OPERATING INSTRUCTIONSRiding at High Altitudes or Sea LevelCAUTION: Failure to re-calibrate may cause serious engine dam-age.Refer to an autho

WARNINGDo not wind starting rope around your hand. Hold rope by thehandle only. Do not start the snowmobile by the drive pulleyunless it is a true em

Fuel Always stop the engine before refueling. Fuel is flammable andexplosive under certain conditions. Always work in a well-venti-lated area. Do not

Wind the rope tightly around drive pulley. When pulled, pulley mustrotate counterclockwise.A03D25A1TYPICAL — FAN-COOLED MODELS1. Knot on this side148_

1A19D13ATYPICAL — LIQUID-COOLED MODELS1. ClipPull the rope using a sharp, crisp pull so the rope comes free of thedrive pulley.Start engine as per usu

Towing Another SnowmobileIf a snowmobile is disabled and must be towed use a rigid towbar,remove the drive belt and tow at moderate speed.CAUTION: Alw

TROUBLESHOOTING2 SHORT BEEPS (WHEN ENGINE IS STARTED) THEN ENGINESTOPS.1. Engine stops automatically after four minutes of idling (with-out depressing

3 SHORT BEEPS PER SECOND. ENGINE OVERHEATING PILOTLAMP ALSO BLINKS.1. Engine is overheating.– Stop engine immediately and allow to cool. Check cooling

ENGINE IS CRANKED BUT FAILS TO START. (cont’d)4. No fuel to the engine (spark plug dry when removed).– Check fuel tank level; turn fuel valve on if ap

ENGINE LACKS ACCELERATION OR POWER. (cont’d)8. Engine is overheating.– On liquid cooled engines, check coolant level, pressure cap,thermostat and for

ENGINE MISFIRES. (cont’d)4. Too much oil supplied to engine.– Improper oil pump adjustment, refer to an authorized SKI-DOO dealer.– On premixed models

SPECIFICATIONSNOTE: Because of its ongoing commitment to product quality andinnovation, BRP reserves the right, at any time, to make changes indesign

FAN-COOLEDMODEL380F 550FSUMMIT/EXP.—9Drive sprocketnumber of teethOthers 10Brake system Hydraulic caliper, self adjustingEXPEDITION—406 mm (16 in)Trac

LAWS AND REGULATIONS Know your local laws.Federal, state, provincial and local government agencies have enact-ed laws and regulations pertaining to t

FAN-COOLEDMODEL380F 550FElectricalLightning system output 340 Watts @ 6000 RPMHeadlamp bulb HI/LOW beam 2x60/55Watts(H-4)Type NGK BR9ESSpark plugGap 0

FAN-COOLEDMODEL380F 550FEXPEDITION—1080 mm (42.5 in)SUMMIT—1118 to 1170 mm(44to46in)Ski stanceOthers 1195 mm (47 in)EXPEDITION—1032 mm (40.6 in)Ski ov

GSX/GTX/MX ZMODEL500 SS 600 HOEngine SystemEngine typeRotax 500 SS,liquid cooledw/Reed valve,R.A.V.E.Rotax 600 HO,liquid cooledw/Reed valve,R.A.V.E.Cy

GSX/GTX/MX ZMODEL500 SS 600 HOMX Z/GSX 25.4 mm (1 in) 25.4 mm (1 in)Track profile heightGTX 22.3 mm (0.88 in)—Deflection 30-35 mm (1-3/16 - 1-3/8 in)T

GSX/GTX/MX ZMODEL500 SS 600 HOMX Z 213 kg (469 lb) 215 kg (474 lb)GSX 227 kg (499 lb)—Official dry weightGTX 235 kg (518 lb)—Ski stance mm (in) 1195 (

GSX/GTX/MX Z/SUMMITMODEL600 HO SDI 800 HOEngine SystemEngine typeRotax 600 HOSDI, liquid cooledw/Reed valve,eR.A.V.E.Rotax 800 HO,Power TEK, liquidcoo

GSX/GTX/MX Z/SUMMITMODEL600 HO SDI 800 HOSUMMIT X—9 (159 in)10 (144/151 in)Drive sprocketnumber of teethOthers10Brake system Hydraulic caliper, self a

GSX/GTX/MX Z/SUMMITMODEL600 HO SDI 800 HOSUMMIT SC-144 SC-151SUMMIT X—SC-144/151/159Rear suspensionOthers SC-4MX Z/GSX 381 mm (15 in)REN./REN. X/GTX40

GSX/GTX/MX Z/SUMMITMODEL600 HO SDI 800 HOMX Z 1105 mm (43.5 in)GSX 1160 mm (45.7 in)GTX 1230 mm (48.4 in)X/RENX 1022 mm (40.2 in)Vehicle overall heigh

GSX/GTX/MX Z/SUMMITMODEL600 HO SDI 800 HORecommended oil (engine)XP-S 2-strokesynthetic blendXP-S mineralinjection oilBrake system fluid SRF (DOT 4) o

RIDING THE VEHICLEBefore venturing on the trails, operate the snowmobile in a restrictedflat area until you are completely familiar with its operation

168_________________________

MAINTENANCEINFORMATION_________________________169

PERIODIC MAINTENANCE CHARTWARNINGIt is recommended that the assistance of an authorizedSKI-DOO dealer be periodically obtained on other compo-nents/s

*10-HOUR OR 500 KM (300 mi)WEEKLY OR EVERY 240 KM (150 mi)MONTHLYOREVERY800KM(500mi)ONCEAYEAROREVERY3200 KM (2000 mi)ONCEAYEAROREVERY6000 KM (3700 mi)

*10-HOUR OR 500 KM (300 mi)WEEKLY OR EVERY 240 KM (150 mi)MONTHLYOREVERY800KM(500mi)ONCEAYEAROREVERY3200 KM (2000 mi)ONCEAYEAROREVERY6000 KM (3700 mi)

*10-HOUR OR 500 KM (300 mi)WEEKLY OR EVERY 240 KM (150 mi)MONTHLYOREVERY800KM(500mi)ONCEAYEAROREVERY3200 KM (2000 mi)ONCEAYEAROREVERY6000 KM (3700 mi)

*10-HOUR OR 500 KM (300 mi)WEEKLY OR EVERY 240 KM (150 mi)MONTHLYOREVERY800KM(500mi)ONCEAYEAROREVERY3200 KM (2000 mi)ONCEAYEAROREVERY6000 KM (3700 mi)

ENGINE SYSTEMAir Filter CleaningA33H0JAAIR FILTER LOCATIONA33H0KAREMOVAL OF FILTER FROM ITS GRILLCheck that the air silencer is clean and dry and prop

Cooling SystemAll Liquid-Cooled ModelsCheck coolant level at room temperature. Liquid should be at coldlevel line (engine cold) of coolant tank.NOTE:

Exhaust SystemThe tail pipe of the muffler should be centered with the exit holein the bottom pan. Exhaust system must be free of rust or leaks.Make s

StoppingBefore riding your snowmobile, you should understand how to stopit. This is done by releasing the throttle and gradually depressingthe brake l

12A33A09A3TYPICAL1. Injection oil reservoir2. Maximum level indicator: 13 mm (1/2 in) from top3. Level marks (1/4, 1/2, 3/4)EPA Certified EnginesMaint

Dealer's ResponsibilityWhen performing service on all 2004 and more recent certified SKI-DOO snowmobiles that carry an emissions control informat

VIA EXPRESS or COURIER MAIL:U.S. Environmental Protection Agency Office of Transportation andAir Quality1310 L Street NWWashington D.C. 20005INTERNET

DRIVE SYSTEMBelt Guard Removal and InstallationWARNINGNEVER operate engine:– without shields and belt guard securely installed– with hood opened or r

1A32C06ATYPICAL1. SlotsBrake Fluid LevelCAUTION: Vehicle must be on a level surface before checkingany fluid levels.Check brake fluid (DOT 4) in reser

A03D22A1TYPICAL — BRAKE FLUID RESERVOIR1. MinimumBrake ConditionWARNINGThe brake mechanism on your snowmobile is an essentialsafety device. Keep this

Remove metal particles from magnet.Refill up to upper mark using recommended oil, refer to SPECIFICA-TIONS.CAUTION: Do not use other unrecommended typ

21A33D0BATYPICAL1. Hair pin2. Adjustment screwDrive Belt ConditionInspect belt for cracks, fraying or abnormal wear (uneven wear, wearon one side, mis

Drive Belt Removal/InstallationWARNINGRemove tether cord cap before performing any maintenanceor adjustment, unless otherwise specified. Vehicle must

1A32D13ATYPICAL1. Tighten to open pulleySlip the belt over the top edge of the sliding half of driven pulley, asshown in previous photo.Slip belt unde

• tool kit (including at least pliers, screwdriver, adjustable wrench)• knife• flashlight.Include other items depending on the length and time of your

A32D14ATYPICALClean sheaves of both pulleys using Pulley flange cleaner (P/N 413711 809).InstallationTo install the drive belt, reverse the removal pr

1A32D15ATYPICAL1. Arrow pointing front of vehicleCAUTION: Do not force or use tools to pry the belt into place, asthis could cut or break the cords in

This adjustable drive pulley allows setting maximum engine RPM inthe vehicle to maintain maximum power.Calibration screws should be adjusted so that a

A16D0GA1TRA DRIVE PULLEY1. Position 1 (not numbered)Each position modifies maximum engine RPM by about 200 RPM.Lower position numbers decrease engine

A16D0HA1TYPICAL1. Loosen just enough to permit rotating of calibrate screwWARNINGNEVER disassemble or modify the drive pulley.Improper assembly or mo

Track ConditionWARNINGRemove tether cord cap before performing any maintenanceor adjustment, unless otherwise specified. Vehicle must beparked in a s

Track Tension and AlignmentNOTE: Track tension and alignment are interrelated. Do not adjustone without the other.WARNINGTo prevent serious injury to

3A32F39A21TYPICAL1. Top tool O-ring positioned at 7.3 kg (16 lb)2. Push on top portion of tool until it contacts the top O-ring3. Measured track defle

123A05F0EATYPICAL1. Adjustment screw2. Loosen lock nut (on so equipped models)3. Loosen screw– Retighten retaining screws and lock nuts (on so equippe

A01F05A1231. Guides2. Slider shoes3. Equal distanceTo Adjust Track Alignment:WARNINGRemove tether cord cap before performing any maintenanceor adjust

SAFETY WARNINGDisregarding any of the safety precautions and instructionscontained in this Operator’s Guide, SAFETY VIDEOCASSETTE oron-product warning

SittingFeet on the running boards, body midway back on seat is an ideal po-sition when operating the snowmobile over familiar, smooth terrain.Knees an

A01F0BA12311. Guides2. Slider shoes3. Tighten on this sideTighten lock nuts (some models only) and retaining screws.WARNINGIf lock nuts are not tight

12A05F0EBTYPICAL1. Retighten (so equipped models)2. Retighten to 48 N•m(35lbf•ft)Restart engine and rotate track slowly to recheck alignment.Repositio

ELECTRICAL SYSTEMBattery ElectrolyteElectric Start Models OnlyThese vehicles are equipped with a maintenance-free battery. Elec-trolyte level can not

REAR SUSPENSIONRear Suspension ConditionVisually inspect all suspension components including slider shoes,springs, wheels, etc.NOTE: During normal dri

STEERING AND FRONT SUSPENSIONVisually inspect steering and front suspension for tightness of com-ponents (steering arms, control arms and links, tie r

BODY/FRAMEVehicle Cleaning and ProtectionRemove any dirt or rust.To clean the entire vehicle, use only flannel cloths or equivalent.CAUTION: It is nec

WARNINGDo not attempt to lift the vehicle by hand alone. Use appro-priate lifting device or have assistance to share lifting stress inorder to avoid

1A33E0DA1. Locking ringTaillightIf taillight bulb is burnt, expose the bulb by removing the red plasticlens. To remove, unscrew the 2 lens screws.Head

1A33E08ATYPICAL1. Knob206_________________________

STORAGE AND PRESEASON PREPARATIONWARNINGHave an authorized SKI-DOO dealer inspect fuel and oilsystems integrity as specified in PERIODIC MAINTENANCEC

PostingA semi-sitting position with the body off the seat and the feet underthe body in a sort of squatting posture, thus allowing the legs toabsorb t

208_________________________

WARRANTY_________________________209

BRP LIMITED WARRANTY NORTH AMERICA:2006 SKI-DOO®SNOWMOBILES1) SCOPE OF THE LIMITED WARRANTYBombardier Recreational Products Inc. (“BRP”)* warrants its

EMISSION-RELATEDCOMPONENTS600 HOSDI800 H.O.POWERT.E.K.Throttle Position Sensor (TPS)X XAir Temperature Sensor (ATS) X XAir Pressure Sensor (APS)X XFue

3) CONDITIONS TO HAVE WARRANTYCOVERAGEThis warranty coverage is available only on 2006 Ski-Doo snowmo-bile purchased as new and unused by its first ow

• Normal wear and tear;• Routine maintenance items, tune ups, adjustments;• Damage caused by failure to provide proper maintenance and/orstorage, as d

Neither the distributor, any BRP dealer nor any other person has beenauthorized to make any affirmation, representation or warranty re-garding the pro

IN USA:BRP US Inc.SKI-DOOCONSUMER SERVICES GROUP7575 BOMBARDIER COURTWAUSAU WI 54401Tel: (715) 848-4957* In the USA, products are distributed and serv

BRP INTERNATIONAL LIMITED WARRANTY:2006 SKI-DOO®SNOWMOBILES1) SCOPE OF THE LIMITED WARRANTYBombardier Recreational Products Inc. (“BRP”) warrants its

3) CONDITIONS TO HAVE WARRANTYCOVERAGEThis warranty coverage is available only on 2006 Ski-Doo snowmo-bile purchased as new and unused by its first ow

KneelingThis position is achieved by placing one foot firmly on the runningboard and the opposite knee on the seat. Avoid abrupt stops.mmo2006-003-003

6) EXCLUSIONSThe following are not warranted under any circumstances:• Normal wear and tear;• Routine maintenance items, tune ups, adjustments;• Damag

7) LIMITATIONS OF LIABILITYTHIS WARRANTY IS EXPRESSLY GIVEN AND ACCEPTED INLIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESSED ORIMPLIED, INCLUDING WITHOU

BOMBARDIER RECREATIONAL PRODUCTS INC.SKI-DOOCONSUMER SERVICES GROUPVALCOURT QC J0E 2L0Tel: (819) 566-3366© 2005 Bombardier Recreational Products Inc.

PRIVACY OBLIGATIONS/DISCLAIMERWe wish to inform you that your coordinates will be used for safetyand warranty purposes. Sometimes, we also use the coo

CHANGE OF ADDRESS OR OWNERSHIPIf your address has changed or if you have sold or given your vehicletoanyone,besuretofilloutandmailthecardprovidedonnex

CHANGE OF ADDRESSCHANGE OF OWNERSHIPVEHICLE IDENTIFICATION NUMBEROLD ADDRESSOR PREVIOUS OWNERNEW ADDRESSOR NEW OWNERNO.CITYNAMESTREETSTATE/PROVINCEAPT

A00A8JBombardierRecreational Products Inc.WARRANTY DEPARTMENT75, J.A. BombardierSherbrooke, QCCanadaJ1L 1W3AFFIXPROPERPOSTAGE224______________________

Mmo-2006 4x6 REV ANG.FH8 Fri Apr 29 15:30:56 2005 Page 1 CompositeC M Y CM MY CY CMY K

StandingPlace both feet on the running boards. Knees should be flexed toabsorb the shock from surface bumps. This is an effective positionto see bette

On snowmobiles allowing two passengers, if you have an adult anda child for passenger, BRP recommends that the child sits in thecenter location. This

For complete information on how to adjust the suspension, pleaserefer to the section of this Operator’s Guide entitled SUSPENSIONADJUSTMENTS under OPE

Frozen WaterTraveling frozen lakes and rivers can be fatal. Avoid waterways. Ifyou are in an unfamiliar area, ask the local authorities or residentsab

DownhillDownhill driving requires that you have full control of your vehicleat all times. On steeper hills, keep your center of gravity low andboth ha

Bright SunshineBright sunny days can considerably reduce your vision. The glarefrom sun and snow may blind you to the extent that you cannot easilydis

Tu rn in gDepending on terrain conditions, there are two preferred ways toturn or corner a snowmobile. For most snow surfaces, “body eng-lish” is the

FOREWORDCongratulations on your purchase of a new SKI-DOO snowmobile.Whatever model you have chosen, it is backed by the BombardierRecreational Produc

Railroad CrossingNever ride on railroad tracks. It is illegal. Railroad tracks and railroadrights-of-way are private property. A snowmobile is no matc

Trails and SignsTrail signs are used to control, direct or regulate the use of snowmo-biles on trails. Become familiar with all signs used in the area

TRACTION ENHANCING PRODUCTSNOTE: This section is applicable only to snowmobile equipped witha track that as been approved for studs.Using more positiv

1) OversteeringIn certain conditions, using more positive carbide ski runners withoutstudding the track could make the snowmobile prone to oversteer-i

2) UndersteeringIn certain conditions, the use of studs could make the snowmobileprone to understeering if the skis are not equipped with more posi-ti

AccelerationStudding the track will allow your sled to accelerate better on packedsnow and ice but will have no noticeable effect on soft snow. Thisca

Studs can also cause serious damage to your snowmobile if it isnot equipped with the tunnel protectors designed for your particularmodel. Damage to th

WARNING– Never stud a track that has not been approved for studs.Approved tracks can be identified by a stud symbol (seeillustration) molded into the

– broken rods– broken studs– bent studs– studs that are torn off the track– missing track guide(s).Replace broken or damaged studs immediately. If you

SAFETY LABELINGSafety standards for snowmobiles have been adopted by the Snow-mobile Safety and Certification Committee (SSCC) of which BRPis a proud

Although the mere reading of such information does not eliminatethe hazard, the understanding and application of the information willpromote the corre

64, 5, 15,17,18101221111163687mmo2006-003-013_a21413141920mmo2006-003-021_aTYPICAL — LOCATION OF IMPORTANT INSTRUCTIONS38_____SAFETY INFORMATION_____

Instruction 1A33A2CAInstruction 2A33A2DAEUROPEAN MODELS/EXPEDITION FAN 550_____SAFETY INFORMATION_____39

Instruction 3A01A2EAInstruction 4Ce garde-courroie doit TOUJOURS être en place lorsque lemoteur fonctionne. Attention aux pièces en rotation _ ellespe

Instruction 5mmo2006-003-006_aFAN-COOLED MODELSInstruction 6Attention aux pièces CHAUDES!Beware of HOT parts!516002664A33A2GA_____SAFETY INFORMATION__

Instruction 7A32A1HALIQUID-COOLED MODELSInstruction 8Use XP-S 2-Stroke Synthetic blendorXP-S Synthetic 2-Stroke oil.Utilisez de l'huilesemi-syn

Instruction 9A33H02ADO NOT SIT HERE / NE PAS SASSEOIR ICISOME MODELS — SINGLE SEAT_____SAFETY INFORMATION_____43

A33A2IADO NOT SIT HERE / NE PAS SASSEOIR ICISOME MODELS — SINGLE SEATInstruction 10516002641TOUS LES CONDUCTEURS ET PASSAGERSDOIVENT LIRE CE QUI SUIT

Instruction 11A33A2KA_____SAFETY INFORMATION_____45

Instruction 12 Lire et comprendre toutes les étiquettes davertissements et le guide du conducteur avant utilisation. Si le guide est introuvab

Instruction 14NEVER SIT IN CARGO AREA.Exceeding maximum cargo loadmay affect steeringcontrol and braking ability.MAXIMUM cargo load :

TABLE OF CONTENTSSAFETY INFORMATIONINTRODUCTION ... 8IMPORTANT BASIC SAFETY MEASURES...

Instruction 17mmo2006-003-009_aFAN COOLED MODELS — NORTH AMERICAmmo2006-003-010_aFAN COOLED MODELS — EUROPE48_____SAFETY INFORMATION_____

Instruction 18mmo2006-003-011_aLIQUID COOLED SUMMIT MODELS — NORTH AMERICA_____SAFETY INFORMATION_____49

mmo2006-003-012_aLIQUID COOLED SUMMIT MODELS — EUROPEInstruction 19A33A39AGTX/EXPEDITION MODELS50_____SAFETY INFORMATION_____

Instruction 20A33A3AAGTX LIMITED ONLYInstruction 21AVERTISSEMENTWARNINGmmo2006-003-007_AEUROPEAN MODELS_____SAFETY INFORMATION_____51

Instruction 22mmo2006-003-008_ASDI AND POWER TEK MODELSInstruction 23512060138ALL MODELS EXCEPT SDI AND POWER TEKInstruction 24704901107vmo2006-005-00

ENVIRONMENTINFORMATION__________________________53

GENERALWildlife compliments your snowmobiling day. Snowmobile tracksprovide firm ground over which animals can travel from area to area.Do not violate

Light Treading refers to more than the thread of our tracks. It's astatement of concern, respect and willingness to take the lead andtake action.

JUST WHAT IS LIGHT TREADING?The fundamental objective of Light Treading is one of respect forwhere and how you ride a snowmobile. You're a light

WHY IS LIGHT TREADING SMARTSnowmobilers know all too well the efforts that have been madethroughout the sport's history to enjoy access to areas

17) Fuel Tank Cap ... 8418) Mechanical Fuel LevelGauge ... 8419) Heating Grip/Thr

58_________________________

VEHICLEINFORMATION__________________________59

HOW TO IDENTIFY YOUR SNOWMOBILEVehicle Description DecalVehicle description decal is located on right hand side of tunnel.mmo2006-003-014_aTYPICAL1. V

Serial NumbersThe main components of your snowmobile (engine and frame) areidentified by different serial numbers. It may sometimes becomenecessary to

Engine Serial Number Location1A25C0MAFAN-COOLED MODELS1. Engine serial number1A32C01BLIQUID COOLED MODELS1. Engine serial number62____________________

CONTROLS/INSTRUMENTS/EQUIPMENTNOTE: Some controls/instruments/equipment do not apply or are op-tional on some models. In these cases their reference n

26A33A36B10 9 2613531216-2417152918 272719761484-11232912TYPICAL1) SpeedometerAll Models except Liquid Cooled SummitThese models are equipped with an

NOTE: As soon as the vehicle is moving, the multifunction displaywill show speed only instead of the selected mode.9A35A03B1012-364857TYPICAL — MODELS

9A35A04B1012-364857MODELS WITH TACHOMETER ONLY1. Brake/parking brake pilot lamp (red)2. Reverse pilot lamp3. DESS pilot lamp4. High beam pilot lamp (b

Oil Pilot LampThis pilot lamp will glow up when injection oil level is low. Stop ve-hicle in a safe place then, replenish injection oil reservoir.Low

TowingAnotherSnowmobile... 150Transporting the Vehicle ... 150TROUBLESHOOTING...

Multifunction Display codeIf your speedometer shows SCALE in the multi-function display, itmeans that the display selector button is stuck in the down

2) TachometerDirect-reading dial indicates the number of thousand of revolutionsper minute (RPM) of the engine.A33E0AATYPICAL — MULTIPLY THE READING B

3) Electric Fuel Level GaugeDash-mounted gauge to facilitate fuellevel reading. This gauge func-tions when engine is running.A32A26A21TYPICAL1. Full2.

4) Temperature GaugeThe gauge indicates engine coolant temperature. The needle movesto the normal range as engine warms. Under all riding conditions,t

6) Brake LeverLocated on the left hand side of handlebar. When squeezed, thebrake is applied. When released, it automatically returns to its orig-inal

All ModelsWhen the engine is running, depressing the START/RER button willcommand the engine to reverse crankshaft rotation as driving thesnowmobile i

Shifting in ReverseAll ModelsWARNINGShifting to reverse mode on these snowmobiles is done bydepressing the START/RER button when the engine is run-ni

To do so, push and hold START/RER button with engine running. Af-ter 2 seconds, one beep is heard meaning that the low altitude modecan be selected. R

11) Ignition SwitchFan Cooled Models1 1223A23H04AMANUAL START/ELECTRIC START MODELS1. OFF2. ON3. STARTManual StartingTo start the engine, first turn t

12) Tether Cut-Out SwitchGeneralWhen the tether cord cap is removed, its shuts the engine off pre-venting snowmobile to runaway if the operator falls

STORAGE AND PRESEASON PREPARATION... 207WARRANTYBRP LIMITED WARRANTY NORTH AMERICA: 2006 SKI-DOO®SNOWMOBILES ...

DESS (Digitally Encoded Security System) Key/Cut-Out SwitchLiquid Cooled ModelsOn these models, the tether cord cap is digitally encoded to provideyou

A30H08A11. Free of dirt or snowA DESS pilot lamp blinking 3 times per second means that you haveinstalled a cap with a code the ECM of this snowmobile

13) Engine Cut-Out SwitchThis push-pull type or toggle type switch (depending on models) islocated on the right hand side of the handlebar. To stop th

1A33E03A2TYPICAL — ALL MODELS EXCEPT SUMMIT1. ON2. OFFAll operators of the snowmobile should familiarize themselves withthe function of this device by

14) Headlamp Dimmer SwitchLocated on left hand side of handlebar, allows selection of headlampbeam. Note that lights are automatically ON whenever the

16) Choke LeverThis device features a 3-position lever to facilitate cold start.123A06H1KA1. OFF2. Position 23. Position 3Initial Cold StartingNOTE: D

17) Fuel Tank CapUnscrew to fill up tank then fully tighten.WARNINGAlways stop the engine before refueling. Fuel is flammableand explosive under cert

Summit XOpen fabric door to see the fuel level through the transparent fueltank.A33H1OA11. Fabric door__________________________85

19) Heating Grip/Throttle Lever SwitchIt is a three-position switch. Select the desired position to keep yourhands at a comfortable temperature.A33E04

20) Rear Passenger Heating Grip SwitchThree-position switch. Select the desired position to keep rear pas-senger's hands at a comfortable tempera

SAFETYINFORMATION______SAFETY INFORMATION_____7

A33H4SB1TYPICAL — BACKREST ADJUSTMENT FOR PASSENGER1. Adjustment handle23) Electric Visor Jack ConnectorAn electric visor can be connected to the jack

Driver1A33A0SA2TYPICAL1. Electric visor jack connector2. Stress relief extension__________________________89

PassengerA33H4TA1GTX LIMITED ONLY1. Electric visor jack connector24) 12-Volt Power OutletA 12-volt electric appliance may be connected to that jack co

A29I04A25) WindshieldWindshield provides operator comfort, as well as protection by de-flecting wind and snow away from the operator.26) Adjustable Mi

• When following another snowmobile which makes snow dust.1A33C01A2TYPICAL1. ON2. OFFCAUTION: When operating the snowmobile above 5°C(41°F),move the c

1A33H0MA21. Anchors2. GrommetsTo open a side panel, stretch and unhook the latches.1A33H13A1. Latch__________________________93

To remove a side panel remove by pulling up both locking devicesfrom hinge.1A33H0EA1. Locking deviceFor left hand side panel removal, also unplug vent

A33C02B1NON-2-TEC MODELS1. Vent hoseA33E0RA12-TEC MODELS1. Sensor__________________________95

Reverse opening procedure to close hood and side panels. Properlyhook up latches.30) FusesTo remove fuse from holder, pull fuse out. Check if filament

1A33E0EATYPICAL1. Ground wire protection fuseAll Models except SDIAccessories FuseAccessoriesareprotectedwith20ampereratedfuse. Seefollowingillustrati